Power7 High-End Power Subsystem Firmware
Applies to: 9125-F2C
This document provides information about the installation of
Licensed
Machine or Licensed Internal Code, which is sometimes referred to
generically
as microcode or firmware.
Contents
This package provides firmware for IBM Power 775 (9125-F2C)
Servers only. Do not use on any other
systems.
The firmware level in this package is:
HMC-Managed Systems
This firmware level requires a minimum HMC level of:
HMC V7 R7.3.0 Service Pack 1.
Go to the following URL to access the HMC code packages:
NOTE: You must be logged in as hscroot in order for
the
firmware installation to complete correctly.
Use the following example as a reference to determine whether your
installation will be concurrent or disruptive.
Note: The file names and service pack levels used in
the
following examples are for clarification only, and are not
necessarily levels that have been, or will be released.
Power Subsystem firmware file naming convention:
02APXXX_YYY_ZZZ
- XXX is the release level
- YYY is the service pack level
- ZZZ is the last disruptive service pack level
NOTE: Values of service pack and last disruptive service
pack level (YYY and ZZZ) are only unique
within a release level (XXX). For example, 02AP730_067_045 and
02AP731_067_045 are different
service packs.
An installation is disruptive if:
- The release levels (XXX) are different.
Example: Currently installed release is AP730, new release is
AP731
- The service pack level (YYY) and the last
disruptive service pack level (ZZZ) are equal.
Example: AP730_061_061 is disruptive, no matter what level of
AP730 is currently
installed on the system
- The service pack level (YYY) currently installed on the system
is lower than the last disruptive service pack level (ZZZ) of the
service pack to be installed.
Example: Currently installed service pack is AP730_120_120 and
new service pack is AP730_152_130
An installation is concurrent if:
- The service pack level (YYY) is higher than the service
pack level currently installed on your system.
Example: Currently installed service pack is AP730_061_061,
new service pack is AP730_070_061.
Firmware Information and Update Description
| Filename |
Size |
Checksum |
| 02AP730_054_054.rpm |
16,853,336 |
38783 |
| 02AP730_054_054
12/05/2011
|
Impact: Function
Severity: SPE
- Enhancements and fixes to Water Conditioning Unit
operation, error detection, and service
- Enhancements and fixes to Fill/Drain tool operation and
service
- Enhancements and fixes to frame's bulk power supply (BPR)
operation and service
- Enhancements and fixes for CEC power supplys to prevent
erroneous power faults and add recovery
- Support to light up the frame roll-up LED when servicing
BPA parts
- Emergency Power Off Warning (EPOW) support for Hot Water /
Hot Room
- Support for unlocking of Disk Enclosure carriers for service
- Increase the number of CECs allowed to power on when
running in low voltage DC range from 4 up to 8
- Many other fixes to service/erroneously generated faults
- Various other general stability/usability fixes
|
| 02AP730_042_042
08/26/2011
|
Impact: New
Severity: NEW
- General Availability Level
|
You can view the frame's current firmware level on the Advanced System
Management Interface (ASMI) Welcome pane. It appears in the top
right
corner. Example: AP730_042.
Follow the instructions on the web page. You must read and agree to
the license agreement to obtain the firmware packages.
Note: If your HMC is not internet-connected you will need to
download the new firmware level to a CD-ROM or ftp server.
The method used to install new firmware will depend on the release
level of firmware which is currently installed on your server. The
release level can be determined by the prefix of the new firmware's
filename.
Example: EPXXX_YYY_ZZZ
Where XXX = release level
- If the release level will stay the same (Example: Level
AP730_075_075 is currently installed and you are attempting to
install level AP730_081_075) this is considered an update.
- If the release level will change (Example: Level AP730_081_075
is currently installed and you are attempting to install level
AP731_096_096) this is considered an upgrade.
Instructions for installing firmware updates and upgrades can be found
at http://publib.boulder.ibm.com/infocenter/systems/scope/hw/topic/ipha1/updateschapter.htm