Power7 System Firmware

• A problem was fixed for a hypervisor deadlock that results in the system being in a "Incomplete state" as seen on the management console.  This deadlock is the result of two hypervisor tasks using the same locking mechanism for handling requests between the partitions and the management console.  Except for the loss of the management console control of the system, the system is operating normally when the "Incomplete state" occurs.
• A security problem was fixed in the lighttpd server on the service processor OpenSSL where a remote attacker, while attempting authentication, could insert strings into the lighttpd server log file.  Under normal operations on the service processor, this does not impact anything because the log is disabled by default.  The Common Vulnerabilities and Exposures issue number is CVE-2015-3200.
  

• On systems using PowerVM with shared processor partitions that are configured as capped or in a shared processor pool, there was a problem found that delayed the dispatching of the virtual processors which caused performance to be degraded in some situations.  Partitions with dedicated processors are not affected.   The problem is rare and can be mitigated, until the service pack is applied, by creating a new shared processor AIX or Linux partition and booting it to the SMS prompt; there is no need to install an operating system on this partition.  Refer to help document http://www.ibm.com/support/docview.wss?uid=nas8N1020863 for additional details.

New features and functions

• Support was added to the Advanced System Management Interface (ASMI) to be able to add a IPv4 static route definition for each ethernet interface on the service processor.  Using a static route definition,  a Hardware Management Console (HMC) configured on a private subnet that is different from the service processor subnet is now able to connect to the service processor and manage the CEC.  A static route persists until it is deleted or until the service processor settings are restored to manufacturing defaults.  The static route is managed with the ASMI panel "Network Services/Network Configuration/Static Route Configuration" IPv4 radio button.  The "Add" button is used to add a static route (only one is allowed for each ethernet interface) and the "Delete" button is used to delete the static route.
  

System firmware changes that affect all systems

• A problem was fixed for the iptables process consuming all available memory, causing an out of memory dump and reset/reload of the service processor.
• A problem was fixed in the Advanced System Management Interface (ASMI) to reword a confusing message for systems with no deconfigured resources.  The "System Service Aids/Deconfiguration Records" message text for this situation was changed from "Deconfiguration data is currently not available." to "No deconfigured resources found in the system.
• A problem was fixed for performance dumps to speed its processing so it is able to handle partitions with a large number of processors configured.  Previously, for large systems, the performance dump took too long in collecting performance data to be useful in the debugging of some performance problems.
• A problem was fixed for a faulty ambient temperature sensor that triggered emergency power offs with SRC 11007203 or 11007203 even though the temperature was not over the limit.  If the ambient temperatures are high now, the errors will be logged for call home service but they will not trigger an emergency power off.
• A problem was fixed to prevent a hypervisor task failure with a B7000602 SRC logged, if multiple resource dumps running concurrently run out of dump buffer space. The failed hypervisor task could prevent basic logical partition operations from working, potentially leading to an Incomplete state on the Management Console.
• For Power7+ systems with shared processor partitions, a problem was fixed that could result in latency or timeout issues with I/O devices.  For the Power7 systems (IBM Power 770 (9117-MMD), IBM Power 780 (9179-MHC)), this issue impacts all partitions, regardless if the processors are shared or not.
• A problem was fixed for a partition deletion error on the management console with error code 0x4000E002 and message "...insufficient memory for PHYP".  The partition delete operation has been adjusted to accommodate the temporary increase in memory usage caused by memory fragmentation, allowing the delete operation to be successful.
• A security problem was fixed in OpenSSL where the service processor would, under certain conditions, accept Diffie-Hellman client certificates without the use of a private key, allowing a user to falsely authenticate .  The Common Vulnerabilities and Exposures issue number is CVE-2015-0205.
• A security problem was fixed in OpenSSL for it's BigNumber Squaring implementation to prevent a failure of cryptographic protection mechanisms.  The Common Vulnerabilities and Exposures issue number is CVE-2014-3570.
• A security problem was fixed in OpenSSL to fix multiple flaws in the parsing of X.509 certificates.  These flaws could be used to modify an X.509 certificate to produce a certificate with a different fingerprint without invalidating its signature, and possibly bypass fingerprint-based blacklisting.  The Common Vulnerabilities and Exposures issue number is CVE-2014-8275.
• A security vulnerability, commonly referred to as GHOST, was fixed in the service processor glibc functions getbyhostname() and getbyhostname2() that allowed remote users of the functions to cause a buffer overflow and execute arbitrary code with the permissions of the server application.  There is no way to exploit this vulnerability on the service processor but it has been fixed to remove the vulnerability from the firmware.  The Common Vulnerabilities and Exposures issue number is CVE-2015-0235.
• A security problem was fixed in OpenSSL where a remote attacker could crash the service processor with a specially crafted X.509 certificate that causes an invalid pointer or an out-of-bounds write.  The Common Vulnerabilities and Exposures issue numbers are CVE-2015-0286 and CVE-2015-0287.
• A problem was fixed that prevented a second management console from being added to the CEC.  In some cases, network outages caused defunct management console connection entries to remain in the service processor connection table, making connection slots unavailable for new management consoles  A reset of the service processor could be used to remove the defunct entries and allow the second management console to connect.
• A problem was fixed for an IPL termination with a B150B10C SRC and B121C770 error logs.  This problem only occurred on a multiple node IBM Power 770 (9117-MMC) or  IBM Power 780 (9179-MHC).  The problem was intermittent so a re-ipl of the CEC normally resolved the problem.
• A problem was fixed for some service processor error logs not getting reported to the OS partitions as needed.  The service processor was not checking for a successful completion code on the error log message send, so it was not doing retries of the send to the OS when that was needed to ensure that the OS received the message.
• A problem was fixed for an incorrect call home for SRC B1818A0F.  There was no problem to be resolved so this call home should have been ignored.
• A security problem was fixed for an OpenSSL specially crafted X.509 certificate that could cause the service processor to reset in a denial-of-service (DOS) attack.  The Common Vulnerabilities and Exposures issue number is CVE-2015-1789.
  

• On a system with redundant service processors, a problem was fixed for bad pointer reference in the mailbox function during data synchronization between the two service processors.  The de-reference of the bad pointer caused a core dump, reset/reload, and fail-over to the backup service processor.
• On systems using PowerVM and Virtual Trusted Platform Module (VTPM) partitions,  a problem was fixed for a Management Console error that occurred while restoring a backup profile that caused the system to go to the Management Console "Incomplete state".  The failed system had a suspended VTPM partition and a B7000602 SRC logged.
  
• For a partition that has been migrated with Live Partition Mobility (LPM) from FW730 to FW740 or later, a problem was fixed for a Main Storage Dump (MSD) IPL failing with SRC B2006008.  The MSD IPL can happen after a system failure and is used to collect failure data.  If the partition is rebooted anytime after the migration, the problem cannot happen.  The potential for the problem existed between the active migration and a partition reboot.
  
• On systems with a PCIe 3D graphics adapter (F/C #EC41 or #EC42) in a partition, a problem was fixed for a partition hang or BA21xxxx error conditions during partition initialization.

System firmware changes that affect all systems

• On systems using Virtual Shared Processor Pools (VSPP), a problem was fixed for an inaccurate pool idle count over a small sampling period.
  
  A problem was corrected for a defect in an earlier service pack (AM770_098) that potentially caused an undetected corruption of firmware when the fix was concurrently activated. If the earlier service pack(AM770_098) was concurrently installed, a platform IPL will mitigate potential future exposure to the problem.
  

• On systems with redundant service processors and unlicensed cores, a problem was fixed with firmware update to prevent SRC B170B838 errors on unlicensed cores after an administrative failover (AFO) to the backup service processor.

New features and functions

• Support was added for using the Mellanox ConnectX-3 Pro 10/40/56 GbE (Gigabit Ethernet) adapter as a network install device.
  

System firmware changes that affect all systems

• A problem was fixed for the Advanced System Manager Interface (ASMI) to change the Dynamic Platform Optimizer (DPO) VET capability setting from "False" to "True".  DPO is available on all systems to use without a license required.  Even though the VET for DPO was set to "False", it did not interfere with the running of DPO.
• A problem was fixed for memory relocation failing during a partition reboot with SRC B700F103 logged.  The memory relocation could be part of the processing for the Dynamic Platform Optimizer (DPO), Active Memory Sharing (AMS) between partitions, mirrored memory defragmentation, or a concurrent FRU repair.
• A security problem was fixed for the Network Time Protocol (NTP) client that allowed remote attackers to execute arbitrary code via a crafted packet containing an extension field.  The Common Vulnerabilities and Exposures issue number is CVE-2009-1252.
• A security problem was fixed in the OpenSSL (Secure Socket Layer) protocol that allowed a man-in -the middle attacker, via a specially crafted fragmented handshake packet, to force a TLS/SSL server to use TLS 1.0, even if both the client and server supported newer protocol versions. The Common Vulnerabilities and Exposures issue number for this problem is CVE-2014-3511.
• A security problem was fixed in OpenSSL for formatting fields of security certificates without null-terminating the output strings.  This could be used to disclose portions of the program memory on the service processor.  The Common Vulnerabilities and Exposures issue number for this problem is CVE-2014-3508.
• Multiple security problems were fixed in the way that OpenSSL handled Datagram Transport Layer Security (DLTS) packets.  A specially crafted DTLS handshake packet could cause the service processor to reset.  The Common Vulnerabilities and Exposures issue numbers for these problems are CVE-2014-3505, CVE-2014-3506 and CVE-2014-3507.
• A security problem was fixed in OpenSSL to prevent a denial of service when handling certain Datagram Transport Layer Security (DTLS) ServerHello requests.  A specially crafted DTLS handshake packet with an included Supported EC Point Format extension could cause the service processor to reset.  The Common Vulnerabilities and Exposures issue number for this problem is CVE-2014-3509.
• A security problem was fixed in OpenSSL to prevent a denial of service by using an exploit of a null pointer de-reference during anonymous Diffie Hellman (DH) key exchange.  A specially crafted handshake packet could cause the service processor to reset.  The Common Vulnerabilities and Exposures issue number for this problem is CVE-2014-3510.
• A security problem in GNU Bash was fixed to prevent arbitrary commands hidden in environment variables from being run during the start of a Bash shell.  Although GNU Bash is not actively used on the service processor, it does exist in a library so it has been fixed.  This is IBM Product Security Incident Response Team (PSIRT) issue #2211.  The Common Vulnerabilities and Exposures issue numbers for this problem are CVE-2014-6271, CVE-2014-7169, CVE-2014-7186, and CVE-2014-7187.
• A problem was fixed for the Advanced System Manager Interface (ASMI) that allowed possible cross-site request forgery (CSRF) exploitation of the ASMI user session to do unwanted tasks on the service processor.
• A problem was fixed for I/O adapters so that BA400002 errors were changed to informational for memory boundary adjustments made to the size of DMA map-in requests.  These DMA size adjustments were marked as UE previously for a condition that is normal.
• A security problem was fixed in OpenSSL for memory leaks that allowed remote attackers to cause a denial of service (out of memory on the service processor). The Common Vulnerabilities and Exposures issue numbers are CVE-2014-3513 and CVE-2014-3567.
• A security problem was fixed in OpenSSL for padding-oracle attacks known as Padding Oracle On Downgraded Legacy Encryption (POODLE).  This attack allows a man-in-the-middle attacker to obtain a plain text version of the encrypted session data. The Common Vulnerabilities and Exposures issue number is CVE-2014-3566.  The service processor POODLE fix is based on a selective disablement of SSLv3 using the Advanced System Management Interface (ASMI) "System Configuration/Security Configuration" menu options.  The Security Configuration options of "nist_sp800_131a", "nist_compat", and "legacy" for affects the disablement SSLv3 and determines the level of protection from POODLE.  The management console also requires a POODLE fix for APAR MB03867(FIX FOR CVE-2014-3566 FOR HMC V7 R7.7.0 SP4 with PTF MH01482) to eliminate all vulnerability to POODLE and allow use of option 1 "nist_sp800_131a" as shown below:
  -1) nist_sp800_131a (SSlv3 disabled):  This highest level of security protection does not allow service processor clients to connect using SSLv3, thereby eliminating any possibility of a POODLE attack.  All clients must be capable of using TLS v1.2 to make the secured connections to the service processor to use this option.  This requires the management console be at a minimum level of HMC V7 R7.7.0 SP4 with POODLE PTF MH01482.
  -2) nist_compat (default mode - SSLv3 enabled for HMC):  This medium level of security protection disables SSLv3 (TLS v1.2 must be used instead) for the web browser sessions to ASMI and for the CIM clients and assures them of POODLE-free connections.  But the older management consoles are allowed to use SSLv3 to connect to the service processor.  This is intended to allow non-POODLE compliant HMC levels to be able to connect to the CEC servers until they can be planned and upgraded to the POODLE compliant HMC levels.  Running a non-POODLE compliant HMC to a service processor in this default mode will prevent the ASMI-proxy sessions from the HMC from connecting as these proxy sessions require SSLv3 support in ASMI.
  -3) legacy (SSLv3 enabled):  This basic level of security protection enables SSLv3 for all service processor client connection.  It relies on all clients being at POODLE fix compliant levels to provide full POODLE protection using the TLS Fallback Signaling Cipher Suite Value (TLS_FALLBACK_SCSV) to prevent fallback to vulnerable SSLv3 connections.  This legacy option is intended for customer sites on protected internal networks that have a large investment in older hardware that need SSLv3 to make browser and HMC connections to the service processor.  The level of POODLE protection actually achieved in legacy mode is determined by the percentage of clients that are at the POODLE fix compliant levels.
  
  Note:  If it is needed to downlevel the system and remove this fix, before doing the firmware update the ASMI Security Configuration should be set to either "nist_compat" or "legacy" to assure that all service processor clients are enforced to the same security level.  An ASMI Security Configuration of "nist_sp800_131a" will  be undefined at the earlier firmware level, causing a mixed-mode of security levels for the clients.
  

• HIPER/Pervasive:  On systems using PowerVM firmware, a performance problem was fixed that may affect shared processor partitions where there is a mixture of dedicated and shared processor partitions with virtual IO connections, such as virtual ethernet or Virtual IO Server (VIOS) hosting, between them.  In high availability cluster environments this problem may result in a split brain scenario.
• DEFERRED:  A performance problem was fixed for PCIe slot C4 which was missing a dedicated internal data buffer, making it a bottleneck when using certain high-performance IO adapters.  The PCIe slot C4 is now assigned a data capability of 16 GB.  This fix pertains only to the IBM Power 750 Express (8408-E8D), IBM Power 760 (9109-RMD), and IBM PowerLinux 7R4 (8248-L4T) systems.  This deferred fix addresses a potential performance problem but not an error condition.  As such,  customers may wait for the next planned service window to activate the deferred fix via a system reboot.
• A problem was fixed to prevent unnecessary EPOW (Emergency and POwer Warning) class 3 event warnings in the OS for ambient temperature approaching specification limit.  This fix pertains only to the IBM Power 750 Express (8408-E8D), IBM Power 760 (9109-RMD), and IBM PowerLinux 7R4 (8248-L4T) systems.
• On systems that have Active Memory Sharing (AMS) partitions and deduplication enabled, a problem was fixed for not being able to resume a hibernated AMS partition.  Previously,  resuming a hibernated AMS partition could give checksum errors with SRC B7000202 logged and the partition would remain in the hibernated state.
• On systems that have Active Memory Sharing (AMS) partitions, a problem was fixed for Dynamic Logical Partitioning (DLPAR) for a memory remove that leaves a logical memory block (LMB) in an unusable state until partition reboot.
• On systems with a F/C 5802 or 5877 I/O drawer installed, a problem was fixed for a hypervisor hang at progress code C7004091 during the IPL or hangs during serviceability tasks to the I/O drawer.
• A problem was fixed that could result in unpredictable behavior if a memory UE is encountered while relocating the contents of a logical memory block during one of these operations:
  - Using concurrent maintenance to perform a hot repair of a node.
  - Reducing the size of an Active Memory Sharing (AMS) pool.
  - On systems using mirrored memory, using the memory mirroring optimization tool.
  - Performing a Dynamic Platform Optimizer (DPO) operation.
• On systems using Virtual Shared Processor Pools (VSPP), a problem was fixed for an inaccurate pool idle count over a small sampling period.
• A problem was fixed for systems in networks using the Juniper 1GBe and 10GBe switches (F/Cs #1108, #1145, and #1151) to prevent network ping errors and boot from network (bootp) failures.  The Address Resolution Protocol (ARP) table information on the Juniper aggregated switches is not being shared between the switches and that causes problems for address resolution in certain network configurations.  Therefore, the CEC network stack code has been enhanced to add three gratuitous ARPs (ARP replies sent without a request received) before each ping and bootp request to ensure that all the network switches have the latest network information for the system.
• On systems using the Virtual I/O Server (VIOS) to share physical I/O resources among client logical partitions, a problem was fixed for memory relocation errors during page migrations for the virtual control blocks.  These errors caused a CEC termination with SRC B700F103.  The memory relocation could be part of the processing for the Dynamic Platform Optimizer (DPO), Active Memory Sharing (AMS) between partitions, mirrored memory defragmentation, or a concurrent FRU repair.
• On systems with redundant service processors,  a problem was fixed so that a backup memory clock failure with SRC B120CC62 is handled without terminating the system running on the primary memory clock.
  

• A problem was fixed for a power off failure of an expansion drawer (F/C 5802 or F/C 5877) during a concurrent repair.  The power off commands to the drawer are now tried again using the System Power Control Network (SPCN) serial connection to the drawer to allow the repair to continue.
  This fix pertains only to IBM Power 770 (9117-MMC) and IBM Power 780 (9179-MHC) systems.
• A problem was fixed for concurrent maintenance to prevent a hardware unavailable failure when doing consecutive concurrent remove and add operations to an I/O Hub adapter for a drawer.
  This fix pertains only to IBM Power 770 (9117-MMC) and IBM Power 780 (9179-MHC) systems.
  

• A problem was fixed that was introduced by AM770_090 / FW770.40, which caused a service processor reset/reload and a SRC B1818601 error log during an IPL when adjusting the speeds of the system fans.  This problem would normally have a successful recovery with a good IPL of the system unless two other reset/reloads of the service processor had occurred within the last 15 minutes.
  

New features and functions

• System recovery for interrupted AC power and Voltage Regulator Module (VRM) failures has been enhanced for systems with multiple CEC enclosures such that a power AC or VRM fault on one CEC drawer will no longer block the other CEC drawers from powering on.  Previously, all CEC enclosures in a system needed valid AC power before the power on of the system could proceed.
  This system recovery feature does not pertain to the IBM Power 750 Express (8408-E8D) , IBM Power 760 (9109-RMD), and IBM PowerLinux 7R4 (8284-L4T) systems because they are single CEC enclosure systems.
  

System firmware changes that affect all systems

• HIPER/Pervasive:  A security problem was fixed in the OpenSSL (Secure Socket Layer) protocol that allowed clients and servers, via a specially crafted handshake packet, to use weak keying material for communication.  A man-in-the-middle attacker could use this flaw to decrypt and modify traffic between the management console and the service processor.  The Common Vulnerabilities and Exposures issue number for this problem is CVE-2014-0224.
• HIPER/Pervasive:  A security problem was fixed in OpenSSL for a buffer overflow in the Datagram Transport Layer Security (DTLS) when handling invalid DTLS packet fragments.  This could be used to execute arbitrary code on the service processor.  The Common Vulnerabilities and Exposures issue number for this problem is CVE-2014-0195.
• HIPER/Pervasive:  Multiple security problems were fixed in the way that OpenSSL handled read and write buffers when the SSL_MODE_RELEASE_BUFFERS mode was enabled to prevent denial of service.  These could cause the service processor to reset or unexpectedly drop connections to the management console when processing certain SSL commands.  The Common Vulnerabilities and Exposures issue numbers for these problems are CVE-2010-5298 and CVE-2014-0198.
• HIPER/Pervasive:  A security problem was fixed in OpenSSL to prevent a denial of service when handling certain Datagram Transport Layer Security (DTLS) ServerHello requests. A specially crafted DTLS handshake packet could cause the service processor to reset.  The Common Vulnerabilities and Exposures issue number for this problem is CVE-2014-0221.
• HIPER/Pervasive:  A security problem was fixed in OpenSSL to prevent a denial of service by using an exploit of a null pointer de-reference during anonymous Elliptic Curve Diffie Hellman (ECDH) key exchange.  A specially crafted handshake packet could cause the service processor to reset.  The Common Vulnerabilities and Exposures issue number for this problem is CVE-2014-3470.
• A problem was fixed that caused frequent SRC B1A38B24 error logs with a call home every 15 seconds when service processor network interfaces were incorrectly configured on the same subnet.  The frequency of the notification of the network subnet error has been reduced to once every 24 hours.
• Help text for the Advanced System Management Interface (ASMI) "System Configuration/Hardware Deconfiguration/Clear All Deconfiguration Errors" menu option was enhanced to clarify that when selecting "Hardware Resources" value of "All hardware resources", the service processor deconfiguration data is not cleared.   The "Service processor" must be explicitly selected for that to be cleared.
• Help text for the Advanced System Management Interface (ASMI) "System Configuration/Power Management/Power Supply Idle Control" menu option was enhanced to clarify that an idle power supply is in a low power state and not powered off.  The new help text states  "Power supply idle mode helps to reduce overall power usage when the system load is very light by having one power supply deliver all the power while the second is in a low power state".
• A problem was fixed that caused a memory clock failure to be called out as failure in the processor clock FRU. This memory clock fix pertains only to the IBM Power 770 (9117-MMC) system.
• A problem was fixed where a 12V DC power-good (pGood) input fault was reported as a SRC 11002620 with the wrong FRU callout of Un-P1 for system backplane.  The FRU callout for SRC 11002620 has been corrected to Un-P2 for I/O card.
• A problem was fixed that caused the slot index to be missing for virtual slot number 0 for the dynamic reconfiguration connector (DRC) name for virtual devices.  This error was visible from the management console when using commands such as "lshwres -r virtualio --rsubtype slot -m machine" to show the hardware resources for virtual devices.
• A problem was fixed that prevented a HMC-managed system from being converted to manufacturing default configuration (MDC) mode when the management console command "lpcfgop -m <server> -o clear" failed to create the default partition.  The management console went to the incomplete state for this error.
• A problem was fixed that caused the Utility COD display of historical usage data to be truncated on the management console.
• A problem was fixed that caused the Advanced System Management Interface (ASMI) menu for Memory Low Power State to be displayed on the IBM Power 770 (9117-MMC) even though it is not applicable to that system.  The 9117-MMC does not the DIMM type required for memory low power state.
  
• A problem was fixed that caused a "code accept" during a concurrent firmware installation from the HMC to fail with SRC E302F85C.
• A power supply fan speed problem was fixed that slowed the power supply fans down to a very low level for a minute about once every hour, with possible thermal shutdown of the power supply.  The affected systems are the Power 750 Express (8408-E8D), Power 760 (9109-RMD), and PowerLinux 7R4 (8248-L4T).
• A power supply problem was fixed to prevent the system from consuming more power than the power supply can support and causing a possible power supply shutdown.  The power supply maximum wattage limit was lowered so that the case of a single power supply unit active for the system (system has redundant supplies) is handled correctly.  The affected systems are the Power 750 Express (8408-E8D), Power 760 (9109-RMD), and PowerLinux 7R4 (8248-L4T).
• A problem was fixed for a Live Partition Mobility (LPM) suspend and transfer of a partition that caused the time of day to skip ahead to an incorrect value on the target system.  The problem only occurred when a suspended partition was migrated to a target CEC that had a hypervisor time that was later than the source CEC.
• A problem was corrected that resulted in B7005300 error logs.
• A  security problem was fixed in the service processor TCP/IP stack to discard illegal TCP/IP packets that have the SYN and FIN flags set at the same time.  An explicit packet discard was needed to prevent further processing of the packet that could result in an bypass of the iptables firewall rules.
• A problem was fixed that prevented guard error logs from being reported for FRUs that were guarded during the system power on.  This could happen if the same FRU had been previously reported as guarded on a different power on of the system.  The requirement is now met that guarded FRUs are logged on every power on of the system.
  

• On systems with a redundant service processor, a problem was fixed where the service processor allowed a clock failover to occur without a SRC B158CC62 error log and without a hardware deconfiguration record for the failed clock source.  This resulted in the system running with only one clock source and without any alerts to warn that clock redundancy had been lost.
  This fix pertains only to the IBM Power 770 (9117-MMC) system.
• On systems with a redundant service processor and one memory clock deconfigured, a problem was fixed where the system failed to IPL using the second memory clock with SRCs B158CC62 and B181C041 logged.
  This fix pertains only to the IBM Power 770 (9117-MMC) system.
• On systems with a F/C 5802 or 5877 I/O drawer installed, a problem was fixed that occurred during Offline Converter Assembly (OCA) replacement operations. The fix prevents a false Voltage Regulator Module (VRM) fault and the logging of SRCs 10001511 or 10001521 from occurring.    This resulted in the OCA LED getting stuck in an on or "fault" state and the OCA not powering on.
• On systems with a redundant service processor with AC power missing to the node containing the anchor card, a problem was fixed that caused an IPL failure with SRC B181C062 when the anchor card could not be found in the vital product data (VPD) for the system.  With the fix, the system is able to find the anchor card and IPL since the anchor card gets its power from the service processor cable, not from the node where it resides.
• On systems running Dynamic Platform Optimizer (DPO) with one or more unlicensed processors, a problem was fixed where the system performance was significantly degraded during the DPO operation.  The amount of performance degradation was more for systems with larger numbers of unlicensed processors.
• On a system with partitions with redundant Virtual Asynchronous Services Interface (VASI) streams,  a problem was fixed that caused the system to terminate with SRC B170E540.  The affected partitions include Active Memory Sharing (AMS), encapsulated state partitions, and hibernation-capable partitions.  The problem is triggered when the management console attempts to change the active VASI stream in a redundant configuration.  This may occur due to a stream reconfiguration caused by Live Partition Mobility (LPM); reconfiguring from a redundant Paging Service Partition (PSP) to a single-PSP configuration; or conversion of a partition from AMS to dedicated memory.
• For a partition with a 256MB Real Memory Offset (RMO) region size that has been migrated from a Power8 system to  Power7 or Power6 using Live Partition Mobility, a problem was fixed that caused a failure on the next boot of the partition with a BA210000 log with a CA000091 checkpoint just prior to the BA210000.  The fix dynamically adjusts the memory footprint of the partition to fit on the earlier Power systems.
• On a system with a disk device with multiple boot partitions, a problem was fixed that caused System Management Services (SMS) to list only one boot partition.  Even though only one boot partition was listed in SMS, the AIX bootlist command could still be used to boot from any boot partition.
• On systems that require in-band flash to update system firmware, a problem was fixed so in-band update would not fail if the Permanent (P) or the Temporary (T) side of the service processor was marked invalid.   Attempting to in-band flash from the AIX or Linux command line failed with a BA280000 log reported.  Attempting to in-band flash from the AIX diagnostics menus also failed because the flash menu options did not appear in this case.
• On systems that have a boot disk located on a SAN,  a problem was fixed  where the SAN  boot disk would not be found on the default boot list  and then the boot disk would have to be selected from SMS menus.  This problem would normally  be seen for new partitions that had tape drives configured before the SAN boot disk.
  

• A problem was fixed that caused Capacity on Demand (COD) "Out of Compliance" messages during concurrent maintenance operations when the system was actually in compliance for the licensed amount of resources in use. This fix pertains only to the IBM Power 770 (9117-MMC) system.
• A problem was fixed for concurrent maintenance operations to limit hardware retries on failed hardware so that it can be concurrently repaired.   This fix pertains only to the IBM Power 770 (9117-MMC) system.
  

• HIPER/Pervasive:  A  security problem was fixed in the OpenSSL Montgomery ladder implementation for the ECDSA (Elliptic Curve Digital Signature Algorithm) to protect sensitive information from being obtained with a flush and reload cache side-channel attack to recover ECDSA nonces from the service processor.  The Common Vulnerabilities and Exposures issue number is CVE-2014-0076.  The stolen ECDSA nonces could be used to decrypt the SSL sessions and compromise the Hardware Management Console (HMC) access password to the service processor.  Therefore, the HMC access password for the managed system should be changed after applying this fix.
• HIPER/Pervasive:  A  security problem was fixed in the OpenSSL Transport Layer Security (TLS) and Datagram Transport Layer Security (DTLS) to not allow Heartbeat Extension packets to trigger a buffer over-read to steal private keys for the encrypted sessions on the service processor.  The Common Vulnerabilities and Exposures issue number is CVE-2014-0160 and it is also known as the heartbleed vulnerability.  The stolen private keys could be used to decrypt the SSL sessions and and compromise the Hardware Management Console (HMC) access password to the service processor.  Therefore, the HMC access password for the managed system should be changed after applying this fix.
• A  security problem was fixed for the Lighttpd web server that allowed arbitrary SQL commands to be run on the service processor.  The Common Vulnerabilities and Exposures issue number is CVE-2014-2323.
• A security problem was fixed for the Lighttpd web server where improperly-structured URLs could be used to view arbitrary files on the service processor.  The Common Vulnerabilities and Exposures issue number is CVE-2014-2324.

• A firmware code update problem was fixed that caused a system failure with SRC B7000103 when the allowed resource usage was exceeded for the partition universal unique identifier (UUID) processing during a code update.
• A firmware code update problem was fixed that caused the Hardware Management Console (HMC) to go to "Incomplete State" for the system with SRC E302F880 when assignment of a partition universal unique identifier (UUID) failed for a partition that was already running.  This problem happens for disruptive code updates from pre-770 levels to 770 or later levels.

New features and functions

• Support was added to upgrade the service processor to openssl version 1.0.1 and for compliance to National Institute of Standards and Technologies (NIST) Special Publications 800-131a.  SP800-131a compliance required the use of stronger cryptographic keys and more robust cryptographic algorithms
• Support was added in Advanced System Management Interface (ASMI) to facilitate capture and reporting of debug data for system performance problems.  The  "System Service Aids/Performance Dump" menu was added to ASMI to perform this function.
• Support was added to the Advanced System Management Interface (ASMI) to provide a menu for "Power Supply Idle Mode".  Using the "Power Supply Idle Mode"  menu, the power supplies can be either set enabled to save power by idling power supplies when possible or set disabled to keep all power supplies fully on and allow a balanced load to be maintained on the power distribution units (PDUs) of the system.  Power supply idle mode enabled helps to reduce overall power usage when the system load is very light by having one power supply deliver all the power while the second power supply is maintained in a low power state.
• Support was added to the Advanced System Management Interface (ASMI) to provide a menu for "Memory Low Power State Control" to enable or disable the custom memory buffer low power mode.  If set to disabled, it disables low power mode (a power-saving feature) to speed memory and improve performance for some workloads.  The "Memory Low Power State Control" menu is not available on the MTM 9117-MMC system because its memory does not have a low power state option.
• Support was added for the IBM Flash 90 (#ES09) PCIe 2.0 x8 eMLC adapter with 900GB storage and 350,00 IOPS read performance.  The system recognizes the PCI device as one needing additional cooling and increases the fan speeds accordingly.
• Support was added in Advanced System Management Interface (ASMI) for saving and restoring network settings using a USB flash drive.
• Support was dropped for Secured Socket Layer (SSL) protocol version 2 and SSL weak and medium cipher suites in the service processor web server (Lighttpd) .  Unsupported web browser connections to the Advanced System Management Interface (ASMI) secured port 443 (using https://) will now be rejected if those browsers do not support SSL version 3.  Supported web browsers for Power7 ASMI are Netscape (version 9.0.0.4), Microsoft Internet Explorer (version 7.0), Mozilla Firefox (version 2.0.0.11), and Opera (version 9.24).
  
• Support was added in Advanced System Management Interface (ASMI) "System Configuration/Firmware Update Policy" menu to detect and display the appropriate Firmware Update Policy (depending on whether system is HMC managed) instead of requiring the user to select the Firmware Update Policy.  The menu also displays the "Minimum Code Level Supported" value.
  

System firmware changes that affect all systems

• The firmware was enhanced to display on the management console the correct number of concurrent live partition mobility (LPM) operations that is supported.
• A problem was fixed that caused a 1000911E platform event log (PEL) to be marked as not call home.  The PEL is now a call home to allow for correction.  This PEL is logged when the hypervisor has changed the Machine Type Model Serial Number (MTMS) of an external enclosure to UTMP.xxx.xxxx because it cannot read the vital product data (VPD), or the VPD has invalid characters, or if the MTMS is a duplicate to another enclosure.
• When powering on a system partition, a problem was fixed that caused the partition universal unique identifier (UUID) to not get assigned, causing a B2006010 SRC in the error log.
• For the sequence of a reboot of a system partition followed immediately by a power off of the partition, a problem was fixed where the hypervisor virtual service processor (VSP) incorrectly retained locks for the powered off partition, causing the CEC to go into recovery state during the next power on attempt.
  
• A problem was fixed that caused the system attention LED to be lit without a corresponding SRC and error log for the event.  This problem typically occurs when an operating system on a partition terminates abnormally.
• A problem was fixed that caused a memory leak of 50 bytes of service processor memory for every call home operation.  This could potentially cause an out of memory condition for the service processor when running over an extended period of time without a reset.
• A problem was fixed that caused a L2 cache error to not guard out the faulty processor, allowing the system to checkstop again on an error to the same faulty processor.
• A problem was fixed that caused a HMC code update failure for the FSP on the accept operation with SRC B1811402 or FSP is unable to boot on the updated side.
• A problem was fixed that caused a SRC B181B2C0 and incorrect hardware callout for a GX bus failure on a wire test.  The SRC B114C80C with GX location codes are now provided to facilitate the repairs for the wire test errors.
• A problem was fixed that caused a built-in self test (BIST) for GX slots to create corrupt error log values that core dumped the service processor with a B18187DA.  The corruption was caused by a failure to initialize the BIST array to 0 before starting the tests.
  
• A problem was fixed that caused a SRC B7006A72 calling out the adapter and the I/O Planar.
• A problem was fixed during resource dump processing that caused a read of an invalid system memory address and a SRC B181C141.  The invalid memory reference resulted from the service processor incorrectly referencing memory that had been relocated by the hypervisor.
  

• On systems with a redundant service processor, a problem was fixed that caused fans to run at a high-speed after a failover to the sibling service processor.
• On systems running AIX or Linux, a problem was fixed that caused the operating system to halt when an InfiniBand Host Channel Adapter (HCA) adapter fails or malfunctions.
• On systems running AIX or linux, a hang in a Live Partition Mobility (LPM) migration for remote restart-capable partitions was fixed by adding a time-out for the required paging space to become available.  If after five minutes the required paging space is not available, the start migration command returns a error code of 0x40000042 (PagingSpaceNotReady) to the management console.
• On systems running Dynamic Platform Optimizer (DPO) with no free memory,  a problem was fixed that caused the Hardware Management System (HMC) lsmemopt command to report the wrong status of completed with no partitions affected.  It should have indicated that DPO failed due to insufficient free memory.  DPO can only run when there is free memory in the system.
• On systems with partitions using physical shared processor pools, a problem was fix that caused partition hangs if the shared processor pool was reduced to a single processor.
• On systems with turbo-core enabled that are a target of logical partition migration (LPM),  a problem was fixed where cache properties were not recognized and SRCs BA280000 and BA250010 reported.
• On 8408-E8D, 9109-RMD, and 8248-L4T systems, the guidance provided by the Advanced System Manager Interface (ASMI) "System Configuration/Hardware Management Console" menu was changed to fix the problem of the serial port not being enabled when converting from a HMC-managed to a non-HMC-managed system.  The enhanced guidance adds a step to reset the service processor when doing the conversion.
• On systems with a redundant service processor, a problem was fixed that caused a guarded sibling service processor deconfiguration details to not be able to be shown in the Advanced System Management Interface (ASMI).
• On systems with a F/C 5802 or 5877 I/O drawer installed, the firmware was enhanced to guarantee that an SRC will be generated when there is a power supply voltage fault.  If no SRC is generated, a loss of power redundancy may not be detected, which can lead to a drawer crash if the other power supply goes down.  This also fixes a problem that causes an 8 GB Fiber channel adapter in the drawer to fail if the 12V level fails in one Offline Converter Assembly (OCA).
• On systems managed by an HMC with a F/C 5802 or 5877 I/O drawer installed, a problem was fixed that caused the hardware topology on the management console for the managed system to show "null" instead of "operational" for the affected I/O drawers.
  
• On systems with a redundant service processor, a problem was fixed that caused a SRC B150D15E to be erroneously logged after a failover to the sibling service processor.
• On Power7+ systems,  a problem was fixed that caused a system checkstop during hypervisor time keeping services.
• DEFERRED:  On Power7 systems, a problem was fixed that caused a system checkstop during hypervisor time keeping services. This deferred fix addresses a problem that has a very low probability of occurrence.  As such customers may wait for the next planned service window to activate the deferred fix via a system reboot.
  
• On systems with a F/C 5802 or 5877 I/O drawer installed, a problem was fixed that where a Offline Converter Assembly (OCA) fault would appear to persist after a OCA micro-reset or OCA replacement.  The fault bit reported to the OS may not be cleared, indicating a fault still exists in the I/O drawer after it has been repaired.
  
• DEFERRED: On Power7 systems, a problem was fixed that caused a system checkstop with SRC B113E504 for a recoverable hardware fault.  This deferred fix addresses a problem that has a very low probability of occurrence.  As such customers may wait for the next planned service window to activate the deferred fix via a system reboot.
  

• A problem was fixed that caused a concurrent hot add/repair maintenance operation to fail on an erroneously logged error for the service processor battery with  SRCs B15A3303, B15A3305, and  B181EA35 reported.
• A problem was fixed that caused a concurrent processor exchange to terminate during node deactivation with SRC B1814616.
• A problem was fixed that caused SRC B15A3303  to be erroneously logged as a predictive error on the service processor sibling after a successful concurrent repair maintenance operation for the real-time clock (RTC) battery.

System firmware changes that affect all systems

• A problem was fixed that caused a migrated partition to reboot during transfer to a VIOS 2.2.2.0, and later, target system. A manual reboot would be required if transferred to a target system running an earlier VIOS release. Migration recovery may also be necessary.
• A problem was fixed that can cause  Anchor (VPD) card corruption and  A70047xx SRCs to be logged.  Note: If a serviceable event  with SRC A7004715 is present or was logged previously, damage to the VPD card may have occurred. After the fix is applied, replacement of the Anchor VPD  card is recommended in order to restored full redundancy. 
  

• On systems running Dynamic Platform Optimizer (DPO) ,  a problem was fixed that caused an incorrect placement of dedicated processors for partitions larger than a single chip.  When this occurs, the performance is impacted over what would have been gained with proper placement.
  

New Features and Functions

• Support for the 8248-L4T.
• Support for 9117-MMC and 9179-MHC with Dynamic Platform Optimization (DPO).

System firmware changes that affect all systems

• A problem was fixed that caused a service processor reset/reload with SRC B181720D due to a memory leak.
• The Hypervisor was enhanced to allow the system to continue to boot using the redundant data chip on the anchor (VPD) card, instead of stopping the Hypervisor boot and logging SRC B7004715,  when the primary data chip on the anchor card has been corrupted.
• The firmware was enhanced to support up to 4200 virtual adapters.
• A problem was fixed that caused a service processor dump to be generated with SRC B18187DA "NETC_RECV_ER" logged.
• The firmware was enhanced to make the Capacity on Demand (CoD) menu option available on the Advanced System Management Interface (ASMI) menus when logged in as admin or celogin.
• The firmware was enhanced to make SRC B15738F8 ("FRUM_ERC_UNEXPECTED_HOTPLUG_ADD") informational instead of predictive.
• A problem was fixed that caused a platform dump generation to fail after a system checkstop with SRCs B181B8A2 and B114E504 ("Processor cleanup failure").
  
• A problem was fixed that caused the date and time to be incorrect in AIX if a partition is remotely restarted on a different system from the one on which it was hibernated.
  
• A problem was fixed that caused a performance loss after a configuration change, such as un-licensing a processor, because the Hypervisor is unable to dispatch a partition to a shared processor.
• A problem was fixed that may cause inaccurate processor utilization reporting.
  

• On systems running Active Memory Sharing (AMS) partitions, a problem was fixed that caused the system to hang after an AMS partition was deleted or mobilized, combined with either an AMS pool resize or relocation of AMS pool memory.
• On systems with I/O towers attached, a problem was fixed that caused multiple service processor reset/reloads if the tower was continuously sending invalid System Power Control Network (SPCN) status data. 
  
• A problem was fixed that was caused by an attempt to modify a virtual adapter from the management console command line when the command specifies it is an Ethernet adapter, but the virtual ID specified is for an adapter type other than Ethernet.  The managed system has to be rebooted to restore communications with the management console when this problem occurs; SRC B7000602 is also logged.
• On systems running Dynamic Platform Optimization (DPO), a problem was fixed that caused the current DPO score for a partition to be incorrect.  When this occurs, it looks like DPO would not improve performance when in fact it would improve the performance.  Also, on systems running Dynamic Platform Optimization (DPO), in which there are no processors in the shared processor pool, a problem was fixed that caused the Hypervisor to become unresponsive (the service processor starts logging time-out errors against the Hypervisor, and the HMC can no longer talk to the Hypervisor) during a DPO operation.
  

New Features and Functions

• Support for the 8408-E8D and 9109-RMD systems.