Power10 System Firmware

Applies to:   9080-HEX

This document provides information about the installation of Licensed Machine or Licensed Internal Code, which is sometimes referred to generically as microcode or firmware.

Contents

1.0 Systems Affected

This package provides firmware for IBM Power System E1080 (9080-HEX) server only.

The firmware level in this package is:

1.1 Minimum HMC Code Level

This section is intended to describe the "Minimum HMC Code Level" required by the System Firmware to complete the firmware installation process. When installing the System Firmware, the HMC level must be equal to or higher than the "Minimum HMC Code Level" before starting the system firmware update.  If the HMC managing the server targeted for the System Firmware update is running a code level lower than the "Minimum HMC Code Level" the firmware update will not proceed.

The Minimum HMC Code levels for this firmware for HMC x86,  ppc64 or ppc64le are listed below.

x86 -  This term is used to reference the legacy HMC that runs on x86/Intel/AMD hardware for the Virtual HMC that can run on the Intel hypervisors (KVM, XEN, VMWare ESXi).
ppc64 or ppc64le - describes the Linux code that is compiled to run on Power-based servers or LPARS (Logical Partitions)
The Minimum HMC level supports the following HMC models:
HMC models: 7063-CR1 and 7063-CR2
x86 - KVM, XEN, VMWare ESXi (6.0/6.5)
ppc64le - vHMC on PowerVM (POWER8,POWER9, and POWER10 systems)

For information concerning HMC releases and the latest PTFs,  go to the following URL to access Fix Central:
http://www-933.ibm.com/support/fixcentral/

For specific fix level information on key components of IBM Power Systems running the AIX, IBM i and Linux operating systems, we suggest using the Fix Level Recommendation Tool (FLRT):
http://www14.software.ibm.com/webapp/set2/flrt/home


NOTES:
                -You must be logged in as hscroot in order for the firmware installation to complete correctly.
                - Systems Director Management Console (SDMC) does not support this System Firmware level.

2.0 Important Information

NovaLink levels earlier than "NovaLink 1.0.0.16 Feb 2020 release" with partitions running certain SR-IOV capable adapters is NOT supported at this firmware release

NovaLink levels earlier than "NovaLink 1.0.0.16 Feb 2020 release" do not support IO adapter FCs EC2R/EC2S, EC2T/EC2U, EC66/EC67 with FW1010 and later. 

Live Partition Mobility (LPM) support restrictions for FW1010.00:

The LPM restrictions given below are for FW1010 as the LPM target system and for FW1010 as LPM source system for the specified Peer System firmware level.
+---------------+-------------------------------+
|            FW1010  LPM  Restrictions          |
+---------------+-------------------------------+
| Peer System   | Result                        |
+---------------+-------------------------------+
| FW8xx         | LPM supported                 |
+---------------+-------------------------------+
| FW910         | LPM supported                 |
+---------------+-------------------------------+
| FW920         | LPM currently not supported   | 
+---------------+-------------------------------+
| FW930         | LPM currently not supported   |
+---------------+-------------------------------+
| FW940         | LPM supported with system key |
| previous to   |                               |
| FW940.41      |                               |
+---------------+-------------------------------+
| FW940.41 and  | LPM supported                 |
| later         |                               |
+---------------+-------------------------------+
| FW941         | LPM supported with system key |
+---------------+-------------------------------+
| FW950         | LPM supported with system key |
| previous to   |                               |
| FW950.20      |                               |
+---------------+-------------------------------+
| FW950         | LPM supported                 |
| FW950.20 and  |                               |
| later         |                               |
+---------------+-------------------------------+
| FW1010        | LPM supported                 |
+---------------+-------------------------------+

 
The following article provides information on how to configure the trusted system key to enable certain cases of LPM support where "with system key" is specified in the above table: https://ibm.biz/Bdf8wz/

vNIC and  Hybrid Network Virtualization (HNV) system configurations are not supported in any migrations to and from FW1010.

Note:  The following IBM document article for the LPM support matrix for POWER10  does not list the cases where FW1010.00 does not have LPM support in the initial  GA, so the above table should be consulted for the specific limitations:
https://www.ibm.com/docs/en/power10?topic=mobility-firmware-support-matrix-partition

2.1 IPv6 Support and Limitations

IPv6 (Internet Protocol version 6) is supported in the System Management Services (SMS) in this level of system firmware. There are several limitations that should be considered.

When configuring a network interface card (NIC) for remote IPL, only the most recently configured protocol (IPv4 or IPv6) is retained. For example, if the network interface card was previously configured with IPv4 information and is now being configured with IPv6 information, the IPv4 configuration information is discarded.

A single network interface card may only be chosen once for the boot device list. In other words, the interface cannot be configured for the IPv6 protocol and for the IPv4 protocol at the same time.

2.2 Concurrent Firmware Updates

Concurrent system firmware update is supported on HMC Managed Systems only.

Ensure that there are no RMC connections issues for any system partitions prior to applying the firmware update.  If there is a RMC connection failure to a partition during the firmware update, the RMC connection will need to be restored and additional recovery actions for that partition will be required to complete partition firmware updates.

2.3 Memory Considerations for Firmware Upgrades

Firmware Release Level upgrades and Service Pack updates may consume additional system memory.
Server firmware requires memory to support the logical partitions on the server. The amount of memory required by the server firmware varies according to several factors.
Factors influencing server firmware memory requirements include the following:
Generally, you can estimate the amount of memory required by server firmware to be approximately 8% of the system installed memory. The actual amount required will generally be less than 8%. However, there are some server models that require an absolute minimum amount of memory for server firmware, regardless of the previously mentioned considerations.

Additional information can be found at:
https://www.ibm.com/support/knowledgecenter/9080-M9S/p9hat/p9hat_lparmemory.htm

2.4 SBE Updates

Power10 servers contain SBEs (Self Boot Engines) and are used to boot the system.  SBE is internal to each of the Power10 chips and used to "self boot" the chip.  The SBE image is persistent and is only reloaded if there is a system firmware update that contains a SBE change.  If there is a SBE change and system firmware update is concurrent, then the SBE update is delayed to the next IPL of the CEC which will cause an additional 3-5 minutes per processor chip in the system to be added on to the IPL.  If there is a SBE change and the system firmware update is disruptive, then SBE update will cause an additional 3-5 minutes per processor chip in the system to be added on to the IPL.  During the SBE update process, the HMC or op-panel will display service processor code C1C3C213 for each of the SBEs being updated.  This is a normal progress code and system boot should be not be terminated by the user. Additional time estimate can be between 12-20 minutes per drawer or up to 48-80 minutes for maximum configuration.

3.0 Firmware Information

Use the following examples as a reference to determine whether your installation will be concurrent or disruptive.

For systems that are not managed by an HMC, the installation of system firmware is always disruptive.

Note: The concurrent levels of system firmware may, on occasion, contain fixes that are known as Deferred and/or Partition-Deferred. Deferred fixes can be installed concurrently, but will not be activated until the next IPL. Partition-Deferred fixes can be installed concurrently, but will not be activated until a partition reactivate is performed. Deferred and/or Partition-Deferred fixes, if any, will be identified in the "Firmware Update Descriptions" table of this document. For these types of fixes (Deferred and/or Partition-Deferred) within a service pack, only the fixes in the service pack which cannot be concurrently activated are deferred.

Note: The file names and service pack levels used in the following examples are for clarification only, and are not necessarily levels that have been, or will be released.

System firmware file naming convention:

01VHxxx_yyy_zzz

NOTE: Values of service pack and last disruptive service pack level (yyy and zzz) are only unique within a release level (xxx). For example, 01VH900_040_040 and 01VH910_040_045 are different service packs.

An installation is disruptive if:

            Example: Currently installed release is 01VH900_040_040, new release is 01VH910_050_050.

            Example: VH910_040_040 is disruptive, no matter what level of VH910 is currently installed on the system.

            Example: Currently installed service pack is VH910_040_040 and new service pack is VH910_050_045.

An installation is concurrent if:

The release level (xxx) is the same, and
The service pack level (yyy) currently installed on the system is the same or higher than the last disruptive service pack level (zzz) of the service pack to be installed.

Example: Currently installed service pack is VH910_040_040, new service pack is VH910_041_040.

3.1 Firmware Information and Description

 
Filename Size Checksum md5sum
01MH1010_064_064.rpm 146217704
 08808
 017825d6046883c2be50e53463f7fbe2 

Note: The Checksum can be found by running the AIX sum command against the rpm file (only the first 5 digits are listed).
ie: sum 01MH1010_064_064.rpm

MH1010
For Impact, Severity and other Firmware definitions, Please refer to the below 'Glossary of firmware terms' url:
http://www14.software.ibm.com/webapp/set2/sas/f/power5cm/home.html#termdefs

The complete Firmware Fix History for this Release Level can be reviewed at the following url:
http://download.boulder.ibm.com/ibmdl/pub/software/server/firmware/MH-Firmware-Hist.html
MH1010_064_064 / FW1010.00

09/17/21		 Impact:  New      Severity:  New

GA Level with key features included listed below.

New Features and Functions
  • This server firmware includes the SR-IOV adapter firmware level xx.30.1004 for the following Feature Codes and CCINs: #EC2R/EC2S with CCIN 58FA; #EC2T/EC2U with CCIN 58FB; and #EC66/EC67 with CCIN 2CF3.
  • Added support in ASMI for a new panel to do Self-Boot Engine (SBE) SEEPROM validation.  This validation can only be run at the service processor standby state.   
    If the validation detects a problem, IBM recommends the system not be used and that IBM service be called.
  • Support was added for a new service processor command that can be used to 'lock' the power management mode, such that the mode can not be changed except by doing a factory reset.
  • Support was changed to disable Service Location Protocol (SLP) by default for newly shipped systems or systems that are reset to manufacturing defaults.  This change has been made to reduce memory usage on the service processor by disabling a service that is not needed for normal system operations. 
  • Support was added to generate a service processor fipsdump whenever there is Hostboot (HB) TI and HB dump.  Without this new support, an HB crash (with an HB dump) does not generate a fipsdump and the FSP FFDC at that point in time. So it was difficult to correlate what was seen in the HB dump to what was happening on the FSP at the time of the HB fail.
  • Support added to Redfish to provide a command to set the ASMI user passwords using a new AccountService schema. Using this service, the ASMI admin, HMC, and general user passwords can be changed.
  • Support for Live Partition Mobility (LPM) to allow LPM migrations when virtual optical devices are configured for a source partition.  LPM automatically removes virtual optical devices as part of the LPM process.  Without this enhancement, LPM is blocked if virtual optical devices are configured.
  • Support for Live Partition Mobility (LPM) to select the fastest network connection for data transfer between Mover Service Partitions (MSPs). The configured network capacity of the adapters is used as the metric to determine what may provide the fastest connection. The MSP is the term used to designate the Virtual I/O Server that is chosen to transmit the partition’s memory contents between source and target servers.
  • Support has been dropped for the smaller logical-memory block (LMB) sizes of 16MB, 32MB, and 64MB. 128MB and 256MB are the only LMB sizes that can be selected in ASMI.
  • Support has been dropped for Active Memory Sharing (AMS) on POWER10 servers.
  • Support for PowerVM for an AIX Update Access Key (UAK) for AIX 7.2.  Interfaces are provided that validate the OS image date against the AIX UAK expiration date. Informational messages are generated when the release date for the AIX operating system has passed the expiration date of the AIX UAK during normal operation. Additionally, the server periodically checks and informs the administrator about AIX UAKs that are about to expire, AIX UAKs that have expired, or AIX UAKs that are missing. It is recommended that you replace the AIX UAK within 30 days prior to expiration.
     For more information, please refer to the Q&A document for "Management of AIX Update Access Keys" at
    https://www.ibm.com/support/pages/node/6480845.
  • Support for LPAR Radix Page Table mode in PowerVM.
  • Support for PowerVM encrypted NVRAM that enables encryption of all partition NVRAM data and partition configuration information.
  • Support for isolating faults to a single node that occur between an SMP cable and two nodes using Time Domain Reflectometry (TDR).
  • Support for booting IBM i from a PCIe4 LP 32Gb 2-port Optical Fibre Channel Adapter with Feature Code #EN1K.
  • Support for VIOS 3.1.3 (based on AIX 7.2 TL5 (AIX 72X) on POWER10 servers.
  • Support for the IBM 4769 PCIe3 Cryptographic Coprocessor hardware security module (HSM).  This HSM has Feature Code #EJ37 with CCIN C0AF.  Its predecessors are IBM 4768, IBM 4767, and IBM 4765.
  • Support for a mainstream 800GB NVME U.2 7 mm SSD (Solid State Drive) PCIe4 drive in a 7 mm carrier with Feature Code #EC7Q and CCIN 59B4 for AIX, Linux, and VIOS.
  • Support for a PCIe4 x16 to CXP Converter card for the attachment of two active optical cables (AOC) to be used for external storage and PCIe fan-out attachment to the PCIe expansion drawers.  This cable card has Feature Code #EJ24 and CCIN 6B53.
  • Support for new PCIe 4.0 x8 dual-port 32 Gb optical Fibre Channel (FC) short form adapter based on the Marvell QLE2772 PCIe host bus adapter (6.6 inches x 2.731 inches). The adapter provides two ports of 32 Gb FC capability using SR optics. Each port can provide up to 6,400 MBps bandwidth. This adapter has feature codes #EN1J/#EN1K with CCIN 579C. 
  • Support for new PCIe 3.0 16 Gb quad-port optical Fibre Channel (FC)l x8 short form adapter based on the Marvell QLE2694L PCIe host bus adapter (6.6 inches x 2.371 inches). The adapter provides four ports of 16 Gb FC capability using SR optics. Each port can provide up to 3,200 MBps bandwidth. This adapter has feature codes #EN1E/#EN1F with CCIN 579A. 

4.0 How to Determine The Currently Installed Firmware Level

You can view the server's current firmware level on the Advanced System Management Interface (ASMI) Welcome pane. It appears in the top right corner. Example: VH920_123.

5.0 Downloading the Firmware Package

Follow the instructions on Fix Central. You must read and agree to the license agreement to obtain the firmware packages.

Note: If your HMC is not internet-connected you will need to download the new firmware level to a USB flash memory device or ftp server.

6.0 Installing the Firmware

The method used to install new firmware will depend on the release level of firmware which is currently installed on your server. The release level can be determined by the prefix of the new firmware's filename.

Example: MHxxx_yyy_zzz

Where xxx = release level

Instructions for installing firmware updates and upgrades can be found at https://www.ibm.com/support/knowledgecenter/9080-M9S/p9eh6/p9eh6_updates_sys.htm

IBM i Systems:

For information concerning IBM i Systems, go to the following URL to access Fix Central: 
http://www-933.ibm.com/support/fixcentral/

Choose "Select product", under Product Group specify "System i", under Product specify "IBM i", then Continue and specify the desired firmware PTF accordingly.

HMC and NovaLink Co-Managed Systems (Disruptive firmware updates only):

 A co-managed system is managed by HMC and NovaLink, with one of the interfaces in the co-management master mode.
Instructions for installing firmware updates and upgrades on systems co-managed by an HMC and Novalink is the same as above for a HMC managed systems since the firmware update must be done by the HMC in the co-management master mode.  Before the firmware update is attempted, one must be sure that HMC is set in the master mode using the steps at the following IBM KnowledgeCenter link for NovaLink co-managed systems:
https://www.ibm.com/support/knowledgecenter/9009-22A/p9eig/p9eig_kickoff.htm

Then the firmware updates can proceed with the same steps as for the HMC managed systems except the system must be powered off because only a disruptive update is allowed.   If a concurrent update is attempted, the following error will occur: " HSCF0180E Operation failed for <system name> (<system mtms>).  The operation failed.  E302F861 is the error code:"
https://www.ibm.com/support/knowledgecenter/9009-22A/p9eh6/p9eh6_updates_sys.htm

7.0 Firmware History

The complete Firmware Fix History (including HIPER descriptions)  for this Release level can be reviewed at the following url:
http://download.boulder.ibm.com/ibmdl/pub/software/server/firmware/MH-Firmware-Hist.html

8.0 Change History


Date
 Description
October 1, 2021
 Updated defect description:  Deleted the following text:OS images with expired UAK dates will not be allowed to be installed and AIX will fail the boot of a partition if image date is after UAK expiration date.  Added underlined text.

Reformatted table for readability.